多攪拌車門以及焊接和焊接實際上是用密封條膠粘的。這也是確保密封的操作。否則，這些縫隙很容易被外界的風或沙填充，從而引起腐蝕等。令人不快的景象。今天，我想與您分享密封條的日常維護。
The multi stirring door and welding and welding are actually glued with sealing strips. This is also the operation to ensure sealing. Otherwise, these gaps are easy to be filled by external wind or sand, resulting in corrosion, etc. An unpleasant sight. Today, I want to share with you the routine maintenance of the sealing strip.
1.檢查自動上料攪拌車的密封件是否有大的裂縫或裂縫。如果密封破裂，可以用粘合劑修好。特別是，在密封件上使用***粘合劑可以輕松填充較大的裂縫區域。當然，如果密封件嚴重損壞或損壞，請更換密封件。
1. Check whether there are large cracks or cracks on the seals of the automatic feeding mixer. If the seal breaks, it can be repaired with adhesive. In particular, the use of * * * adhesive on the seal can easily fill large crack areas. Of course, if the seal is seriously damaged or damaged, replace the seal.
2.在駕駛員用混凝土混合清潔劑清潔門窗密封條之后，應涂一層滲進防護劑，以防止密封條老化，并顯著提高密封條的密封性能。另外，密封條之間的間隙容易充滿灰塵和銹蝕。為此，您需要使用刷子除去灰塵。
2. After the driver cleans the door and window sealing strip with concrete mixed detergent, a layer of penetrating protective agent shall be applied to prevent the sealing strip from aging and significantly improve the sealing performance of the sealing strip. In addition, the gap between sealing strips is easy to be filled with dust and rust. To do this, you need to use a brush to remove dust.
3.更換整個機身時，有必要在焊接部分的重疊部分涂一層密封劑。粘合劑層的厚度約為1mm，并且粘合劑層沒有不適當的粘合，氣泡和其他缺陷。地板的整個底面和前輪蓋的底面應涂3mm-4mm的彈性涂層和防腐涂層。這些措施不僅顯著提高了車身的密封性能，減緩了車身的腐蝕速度，而且大大提高了乘坐舒服程度。
3. When replacing the whole fuselage, it is necessary to apply a layer of sealant on the overlapping part of the welding part. The thickness of the adhesive layer is about 1mm, and the adhesive layer is free from improper bonding, bubbles and other defects. The entire bottom surface of the floor and the bottom surface of the front wheel cover shall be coated with 3mm-4mm elastic coating and anti-corrosion coating. These measures not only significantly improve the sealing performance of the body, slow down the corrosion rate of the body, but also greatly improve the ride comfort.
4.密封門和門是一個相對困難的部分。密封要求相對嚴格。要密封的部分相對較長，要密封的部分的橫截面形狀不相同，并且門經常被打開和關閉。在混凝土攪拌車上安裝3向和4向密封墊，并安裝前支柱和頂梁側梁的4密封結構。這種類型的多通道密封通常放置在前門之間的間隙中，除了具有密封功能外，還具有減少車輛噪音的作用。
4. Sealing doors and doors is a relatively difficult part. The sealing requirements are relatively strict. The part to be sealed is relatively long, the cross-sectional shape of the part to be sealed is different, and the door is often opened and closed. Install 3-way and 4-way gaskets on the concrete mixer, and install the 4-way sealing structure of the front pillar and top beam side beam. This type of multi-channel seal is usually placed in the gap between the front doors. In addition to the sealing function, it also reduces vehicle noise.
5.車窗玻璃損壞后，駕駛員應在更換玻璃時檢查密封條是否損壞。除了能夠輕松地拉起和提起車窗玻璃外，還應注意車窗玻璃周圍的密封，因為維修后車窗通常不會恢復其原始形狀。如果玻璃與玻璃罐之間的間隙不均勻，則橡膠條在玻璃與玻璃罐之間的接觸不良，驅動器很容易用手拉動密封圈。
5. After the window glass is damaged, the driver should check whether the sealing strip is damaged when replacing the glass. In addition to being able to easily pull up and lift the window glass, attention should also be paid to the sealing around the window glass, because the window will not return to its original shape after maintenance. If the gap between the glass and the glass can is uneven, the rubber strip has poor contact between the glass and the glass can, and the driver can easily pull the sealing ring by hand.
6.更換車頂時，駕駛員需要先壓裝并在車頂周圍涂上一層導電密封膠。焊接后，在流道和接頭上涂卷邊膠。這不僅有助于身體。密封件可以防止因法蘭焊縫中積水而引起的過早腐蝕。
6. When replacing the roof, the driver needs to press fit and apply a layer of conductive sealant around the roof. After welding, apply crimping glue on the flow channel and joint. This not only helps the body. The seal can prevent premature corrosion caused by ponding in the flange weld.
7.自動上料攪拌車的天窗是大多數家庭用車的基本配置。當您打開汽車的天窗時，橡膠密封導軌會暴露在空氣中，這不可避免地會積聚灰塵，甚至會進入小礫石中。長期使用后，天窗可能會因磨損而變形，排水口可能會堵塞。
7. The skylight of automatic loading mixer truck is the basic configuration of most family cars. When you open the sunroof of the car, the rubber seal guide rail will be exposed to the air, which will inevitably accumulate dust and even enter the small gravel. After long-term use, the sunroof may be deformed due to wear and the drain may be blocked.
密封條只是機身的一小部分，但它可以確保門的穩定性和重量，保護內部免受風，雨，灰塵，熱量和噪音的影響，并可以裝飾門的邊緣和窗戶。當車身振動或扭曲時，密封條還可以用作減震器和減震器以保護玻璃。因此，混凝土攪拌車的維護不是一件容易的事，并且連接也不容忽視。
The sealing strip is only a small part of the fuselage, but it can ensure the stability and weight of the door, protect the interior from wind, rain, dust, heat and noise, and decorate the edges of the door and windows. When the body vibrates or distorts, the sealing strip can also be used as a shock absorber and shock absorber to protect the glass. Therefore, the maintenance of concrete mixer truck is not an easy task, and the connection can not be ignored.
點擊撥打服務熱線：400-879-1999
2022-12-23
首頁
產品
電話
置頂